α40
High-Speed
High Precision Press
α40
High-speed precision best-selling models with actual sales of more than 3000 units
1. It can correspond to a variety of production and processing methods
Terminals, IC lead frames, motor cores, chains, washers, etc. processing
2. High precision machining with four guide columns and two plungers (220L, 220TL, 330L are 3 plungers)
3. High rigidity thickened main frame
4. Adopt linear bearing to guide
5. Ensure excellent bottom dead center accuracy (cold & hot constant temperature device is standard)
6. A variety of additional options are available
Ultra High Speed
High Precision Press
MXM80
1. High bottom dead center accuracy
2. The highest number of revolutions
MXM-20HSL:2500SPM
3. Design of cold and hot constant temperature
Stable bottom dead center during continuous operation
4. Reduce noise and vibration to extend the life of the mold
5. Large screen operation touch screen / with automatic setting device
6. A wider worktable can be applied to large molds
MXM80
NXT-125
Link Precision
Stamping Press
NXT-125
1. Toggle structure
4 guide post 2 plunger guide punch
2. Automatic setting device
Reduced preparation time
Stroke length·Stroke speed·Die height·Feeding length·Release angle
Feeding line height (optional setting)
3. The slider stroke can be adjusted to correspond to various processing
4. The main frame of the machine tool with high rigidity
Slider frame: high rigid frame FCD50
Workbench S45C
5. Reduce noise and vibration
Reduce stamping skipping and extend die life
More Products
1. Super large worktable, which can be used for 2300mm large die stamping processing 2, 4 guide posts 3 plunger structure can resist high eccentric load * a-80, 125, 125L201I, EPS-80 are 2 plungers 3. Achieve the highest number of revolutions 4. It can achieve the precise dynamic accuracy that can be achieved by small precision punches. 5. The high rigid frame structure can resist high eccentric load. 6. The large swing control device developed by our company can be used for 1500spm
Ultra-high speed crankshaft precision punch
General-purpose high-precision best-selling model 1. High-performance, high-cost punch 2. Dual-axis 8-sided slider long guide 3. The slider is a high-rigidity box structure 4. High-rigidity one-piece casting bed 5. High torque clutch & brake Dry clutch & brake plate 6. Wide table size can be applied to larger molds
The Straight Side Press
1. Ultra-high rigid main frame Comprehensive clearance and bending amount are less than 1/4 of the conventional cold forging press 2. 10mm above the bottom dead center reaches the maximum stamping capacity *MVP-300 3, 4 guide pillars 2 plunger guide structure 4. Variable stroke type * MVP-600 5. Conversion from cutting to stamping 6. Reasonable toggle movements Stop motion within 60° of bottom dead center
Precision Cold Forging Progressive Press
Challenge the speed of light 1. Achieve the world's highest speed 4000SPM (F1HS) 2. Using light material slider to make the bottom dead center accuracy stable The slider uses a special alloy, (High-speed machine tool adopts standard slider material configuration) 3. Use special fluid bearings No contact with metals, control shaking resistance 4. Using piston pin method Minimize the comprehensive clearance, support high eccentric load 5. Standard dynamic balancer Low vibration even when running at high speed
Ultra High Speed High Precision Press
1. Compact design The punch press with the same production capacity in the past has reduced the size of the punch by one third 2. Forming from a good stamping product 3000spm can also be stamped into good products at one time 3. Excellent operating performance Manual cranking is possible in standard mode Reduce preparation time according to the servo drive * 3000spm continuous processing, spm50 inch movement can be set instantaneously 4. The final achievable accuracy Flatness: 1μm「JIS special grade 12μm」 Parallelism: 2um「JIS special grade 14um」 Verticality: 0.4μm「JIS special grade 8μm」 Data of ALT-3 5. Environmental protection type punch Power consumption: save 70% CO2 emissions: reduced by 70%, fuel consumption: reduced by 60%. *Comparison between OMEGA-F1 and ALT-3- 6. Easier to change settings
Super high speed servo punch
High-speed precision best-selling models with actual sales of more than 1,000 units 1. It can correspond to various production and processing methods, such as processing terminals, IC lead frames, motor cores, chains, and washers. 2. High precision machining with four guide columns and two plungers (220L, 220TL. 330L is a 3 plunger type) 3. High rigidity thickened main frame 4. Adopt linear bearing to guide 5. Ensure excellent bottom dead center accuracy (cold & hot constant temperature device is standard) 6. A variety of additional options are available
High-Speed, High Precision Press
1. More subtle control than artificial intelligence, can achieve high precision when used all over the world, and automatically control thermal displacement 2. Bottom dead center position recording function (optional) 3. Visual fine control, direct measurement of product portrait, feedback of bottom dead center control (optional)- 4. The variable stroke mechanism can set the stroke length according to the processing method and widen the worktable (i-MX45XL, i-MX50XL) 5. Outstanding operability, large touch screen, automatic setting function 6. Integrated soundproof speaker (optional)
Next Generation BDC Control Intelligent Press
About Us
Dongguan Sichuang Precision Machinery Co., Ltd.
Dongguan Sichuang Precision Machinery Co., Ltd. was established on September 14, 2020. It is located on the 1st floor of No. 32 Wangkeng Road, Matigang, Dalingshan, Dongguan City, Guangdong Province. Business scope includes maintenance, research and development: punch presses, mechanical equipment, general mechanical equipment, automation equipment, mechanical accessories; sales: punch press, mechanical equipment, general mechanical equipment, automation equipment, mechanical accessories, lubricants; installation: general mechanical equipment, mechanical equipment , Automation equipment, machinery accessories; leasing: machinery and equipment, general machinery and equipment; commodity information consulting services; import and export of goods or technologies (except for the import and export of goods and technologies that are prohibited by the state or involve administrative approval). (Projects that are subject to approval in accordance with the law can only carry out business activities after being approved by relevant departments)
News
ADD.:
Wangkeng Road, Matigang, Dalingshan, Dongguan City, Guangdong Province, China
分享
Time of issue:2021-06-30 15:01:23
Copyright© 2021 Dongguan Sichuang Precision Machinery Co., Ltd. All rights reserved
Copyright© 2021 Dongguan Sichuang Precision Machinery Co., Ltd. All rights reserved
搜索