Language
soso
Homepage
/
News
/
Technical Issues
/
What should I do if the high-speed punch fails?

What should I do if the high-speed punch fails?

  • Categories:Technical Issues
  • Author:
  • Origin:
  • Time of issue:2021-07-03 13:27
  • Views:

(Summary description)The more common faults are mainly: 1. The inching or interlocking of the high-speed punch cannot be operated due to some reasons, so that the punch cannot be stopped in time; 2. The red light will not be dimmed for the second time, and it will be on all the time; 3. Punch The electric slider cannot be adjusted automatically; 4. The counter cannot work normally, etc.

What should I do if the high-speed punch fails?

What should I do if the high-speed punch fails?

What should I do if the high-speed punch fails?

What should I do if the high-speed punch fails?

(Summary description)The more common faults are mainly: 1. The inching or interlocking of the high-speed punch cannot be operated due to some reasons, so that the punch cannot be stopped in time; 2. The red light will not be dimmed for the second time, and it will be on all the time; 3. Punch The electric slider cannot be adjusted automatically; 4. The counter cannot work normally, etc.

  • Categories:Technical Issues
  • Author:
  • Origin:
  • Time of issue:2021-07-03 13:27
  • Views:
Information
The more common faults are mainly: 1. The inching or interlocking of the high-speed punch cannot be operated due to some reasons, so that the punch cannot be stopped in time; 2. The red light will not be dimmed for the second time, and it will be on all the time; 3. Punch The electric slider cannot be adjusted automatically; 4. The counter cannot work normally, etc.
 
The following mainly talks about the causes of the first two failures and the solutions to these two failures.
 
The first is that the inching or interlocking of the high-speed punch cannot be operated due to some reasons. There are many reasons why it cannot be operated. The first point is that the button switch of the punch has a fault during the switch, and then just replace the broken switch. The second point is that the line of the high-speed punching machine has fallen off or broken, causing the press line to malfunction. At this time, the damaged line must be removed and replaced with a new line. The third point is that the PC control input terminal of the punch press is abnormal, which means that the PC controller of the high-speed punch press has a fault. This requires professional maintenance personnel to check the PC controller and repair it.
 
Then the red light will not dim after the second fall. The reason for the constant light is that the gap between the clutch and brake of the punch is too large and it is not adjusted back. This will lead to the extension of the braking time and the change of the angle. At this time, just refer to The adjustment method of the clutch and brake is just fine to adjust the gap back; the reason may also be that the punch is overloaded. At this time, the red light will fail when the red light is turned off twice, and even the punch will stop working.
 
When using a high-speed punch, if there is a failure, first do not worry, first find out the cause of the failure, and prescribe the right medicine for this cause, and you can easily solve it. 
Previous: What is a high-speed punch lock?
Next: What is the general difference in the stamping stroke of a high-speed punch?
Previous: What is a high-speed punch lock?
Next: What is the general difference in the stamping stroke of a high-speed punch?

More Information

How to operate the high speed punch [ 2023-07-13 ]
High-speed presses have two kinds of open presses and closed presses, and their continuous stamping speed is more than 100 times, (small and medium-sized tonnage can currently reach 800-1000 times). The operation of high-speed punching machine need to pay attention to the following matters: 1, high-speed punching machine must not appear oil cut-off phenomenon, due to the fast rush, the movement of the heat, generally take thin oil circulation lubrication, oil cut-off is easy to cause stuffy car failure; 2, no overload use, the load of high-speed punching machine can not be as short time overload problem as conventional punching machine, high-speed punching machine general load is recommended to use about 50-70% of the nominal force to ensure the stiffness of the fuselage; 3, high-speed punching is not recommended to use a single stamping, high-speed punching machine with a single stamping will lose the significance and efficiency of high-speed punching, and a single operation braking Angle is large, the upper dead point is not easy to stop; 4, the high-speed punching machine supporting the unwinding, leveling, feeding device to match the punch speed of the punching machine, can not be mistakenly sent or feed is not timely card phenomenon, in the mold debugging to work more to solve; 5, high-speed punching machine waste collection should be timely. Normal operation, boot lubrication, start the motor, after normal operation (some high-speed presses may warm the machine), and then operate stamping.
Ultra-high speed crankshaft precision punch-Dongguan Sichuang [ 2023-03-18 ]
1. Super large worktable, which can be used for 2300mm large die stamping processing 2, 4 guide posts 3 plunger structure can resist high eccentric load * a-80, 125, 125L201I, EPS-80 are 2 plungers 3. Achieve the highest number of revolutions 4. It can achieve the precise dynamic accuracy that can be achieved by small precision punches. 5. The high rigid frame structure can resist high eccentric load. 6. The large swing control device developed by our company can be used for 1500spm
High-Speed, High Precision Press [ 2022-08-01 ]
High-speed precision best-selling models with actual sales of more than 3000 units 1. It can correspond to a variety of production and processing methods Terminals, IC lead frames, motor cores, chains, washers, etc. processing 2. Four guide pillars and two plungers guide high-precision machining (220L, 220TL, 330L are 3 plunger types) 3. High rigidity thickened main frame 4. Adopt linear bearing to guide 5. Ensure excellent bottom dead center accuracy (Standard cold & hot thermostat device) 6. A variety of additional options are available   Dongguan Sichuang Precision Machinery Co., Ltd. is located in Dalingshan Town, Dongguan City, Guangdong Province. It is a professional agent for Yamada Punch from Japan.
Dongguan Si Chuang Precision, YAMADADOBBY high-speed punch [ 2022-07-05 ]
Dongguan Si Chuang Precision operates Yamada punch, YAMADADOBBY high-speed punch, KYORI punch, Japanese high-speed punch, YAMADA DOBBY and so on. In order to achieve the ultimate punching accuracy, our company is equipped with micron-precision machining equipment, and integrates the processing, assembly and design of our company for R&D and production. The company now has the world's high-speed high-speed punch, 2-micron precision intelligent punch, and provides automatic riveting production lines for motor cores and other machinery.
Ultra-high-speed servo punch [ 2022-01-20 ]
1. Compact design A punch press with the same production capacity as before, one-third smaller 2. Forming from one stamping good product 3000spm can also be stamped and formed at one time 3. Excellent operating performance Manual cranking is possible in standard mode Reduced setup time due to servo drive * 3000spm continuous processing, spm50 inch can be set instantaneously 4. The ultimate accuracy Flatness: 1μm "JIS Premium 12μm" Parallelism: 2um "JIS Premium 14um" Verticality: 0.4μm "JIS Premium 8μm" Apply for ALT-3 data 5. Environmentally friendly punch

ADD.:

Wangkeng Road, Matigang, Dalingshan, Dongguan City, Guangdong Province, China

FAX:

+86-769-82868446

分享

Time of issue:2021-06-30 15:01:23

Copyright© 2021  Dongguan Sichuang Precision Machinery Co., Ltd.  All rights reserved

粤ICP备2021090377号    Powered by www.300.cn

Copyright© 2021  Dongguan Sichuang Precision Machinery Co., Ltd.  All rights reserved

粤ICP备2021090377号    Powered by www.300.cn

搜索
Search