Company Profile: Dongguan Sichuang Precision Machinery Co., Ltd. is located in Dalingshan Town, Dongguan City, Guangdong Province. It specializes in R&D, sales, installation, repair and leasing of presses and automated machinery, as well as spare‑parts supply. The main products include Japanese high‑speed precision presses such as YAMADA DOBBY, AIDA, KYORI and Keen. It delivers one‑stop stamping equipment solutions for connector and new‑energy component manufacturers.

High-speed presses have two kinds of open presses and closed presses, and their continuous stamping speed is more than 100 times, (small and medium-sized tonnage can currently reach 800-1000 times). The operation of high-speed punching machine need to pay attention to the following matters: 1, high-speed punching machine must not appear oil cut-off phenomenon, due to the fast rush, the movement of the heat, generally take thin oil circulation lubrication, oil cut-off is easy to cause stuffy car failure; 2, no overload use, the load of high-speed punching machine can not be as short time overload problem as conventional punching machine, high-speed punching machine general load is recommended to use about 50-70% of the nominal force to ensure the stiffness of the fuselage; 3, high-speed punching is not recommended to use a single stamping, high-speed punching machine with a single stamping will lose the significance and efficiency of high-speed punching, and a single operation braking Angle is large, the upper dead point is not easy to stop; 4, the high-speed punching machine supporting the unwinding, leveling, feeding device to match the punch speed of the punching machine, can not be mistakenly sent or feed is not timely card phenomenon, in the mold debugging to work more to solve; 5, high-speed punching machine waste collection should be timely. Normal operation, boot lubrication, start the motor, after normal operation (some high-speed presses may warm the machine), and then operate stamping.

1. Super large worktable, which can be used for 2300mm large die stamping processing 2, 4 guide posts 3 plunger structure can resist high eccentric load * a-80, 125, 125L201I, EPS-80 are 2 plungers 3. Achieve the highest number of revolutions 4. It can achieve the precise dynamic accuracy that can be achieved by small precision punches. 5. The high rigid frame structure can resist high eccentric load. 6. The large swing control device developed by our company can be used for 1500spm

High-speed precision best-selling models with actual sales of more than 3000 units 1. It can correspond to a variety of production and processing methods Terminals, IC lead frames, motor cores, chains, washers, etc. processing 2. Four guide pillars and two plungers guide high-precision machining (220L, 220TL, 330L are 3 plunger types) 3. High rigidity thickened main frame 4. Adopt linear bearing to guide 5. Ensure excellent bottom dead center accuracy (Standard cold & hot thermostat device) 6. A variety of additional options are available   Dongguan Sichuang Precision Machinery Co., Ltd. is located in Dalingshan Town, Dongguan City, Guangdong Province. It is a professional agent for Yamada Punch from Japan.

Dongguan Si Chuang Precision operates Yamada punch, YAMADADOBBY high-speed punch, KYORI punch, Japanese high-speed punch, YAMADA DOBBY and so on. In order to achieve the ultimate punching accuracy, our company is equipped with micron-precision machining equipment, and integrates the processing, assembly and design of our company for R&D and production. The company now has the world's high-speed high-speed punch, 2-micron precision intelligent punch, and provides automatic riveting production lines for motor cores and other machinery.

1. Compact design A punch press with the same production capacity as before, one-third smaller 2. Forming from one stamping good product 3000spm can also be stamped and formed at one time 3. Excellent operating performance Manual cranking is possible in standard mode Reduced setup time due to servo drive * 3000spm continuous processing, spm50 inch can be set instantaneously 4. The ultimate accuracy Flatness: 1μm "JIS Premium 12μm" Parallelism: 2um "JIS Premium 14um" Verticality: 0.4μm "JIS Premium 8μm" Apply for ALT-3 data 5. Environmentally friendly punch

1. The easiest way is to unload the oil pressure, the motor is reversed, the speed is the fastest, and the balance air is adjusted to the highest pressure, the mode is adjusted to inching, and the inching test is performed. 2. You can top the gear, but be careful not to hurt the gear 3. Cut the mold feet

Place of Origin: YAMADA DOBBY, Japan Nominal pressure: 25T Year: 1999 Nominal pressure stroke: 15-30mm Travel speed per minute: 180-1100spm Worktable size: 640*450*80mm Slider adjustment amount: 50mm Maximum closed working height: 234-235mm Main motor: 11kw*4 Dongguan Sichuang Precision Machinery Co., Ltd.: Precision high-speed punches, high-speed punches, mainly provide precision high-speed punches, gantry punches, C-type high-speed punches, selected imported materials, wear-resistant, corrosion-resistant. Balanced center of gravity, stable performance, high precision , Affordable prices, factory direct sales, support customization, and door-to-door delivery. Japanese agent yamada, with a large inventory of commonly used models, and all products are imported from Japan! Provide professional technical support, provide high-quality after-sales service, and reasonable prices! 7*24 hours service online

1. High bottom dead center accuracy 2. The highest number of revolutions MXM-20HSL:2500SPM 3. Design of cold and hot constant temperature Stable bottom dead center during continuous operation 4. Reduce noise and vibration to extend the life of the mold 5. Large screen operation touch screen / with automatic setting device 6. The wider workbench can be suitable for large molds